AVR ATMega128

 

 

 AVR-MT-128 DEVELOPMENT BOARD FOR ATMEGA128 AVR MICROCONTROLLER WITH JTAG AND STKxxx COMPATIBLE 10 PIN ICSP

FEATURES:

• MCU: ATMega128-16AI with128K Bytes Program Flash, 4K Bytes data EEPROM, 4K Bytes RAM
• JTAG connector for in-circuit programming and debugging with AVR-JTAG
• ICSP 5x2 (10) pin STKxxx compatible connector for in-circuit programming with AVR-PG1B or AVR-PG2B
• RS232 connector with TTL levels
• RS232 interface circuit with Tx, Rx signals
• RS232 DB9 female connector
• Dallas touch button port
• Frequency input
• LCD 16x2 display
• LED status
• five buttons
• Buzzer
• power supply circuit +5V, 78L05 with plug-in power jack and diode bridge
• 32 768 Hz oscillator crystal
• 16 Mhz crystall oscillator
• power supply filtering capacitor
• RESET supervisor IC ZM33064
• RELAY with 10A/250VAC NO and NC contacts with screw terminals
• extension headers for unused in the schematic ports available for external connection
• PCB: FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• four mounting holes 3.3 mm (0.13")
• Dimensions: 120x38 mm (4.7x1.5")

DOCUMENTS:

• AVR-MT-128.pdf user manual

HARDWARE:

• AVR-MT-128 REV.A schematic
• AVR JTAG connector (top view)
• AVR ICSP connector (top view)

SOFTWARE:

• AVR-MT-128 button demo code (C source and HEX)
• AVR-MT-128 LCD demo code ( C source and HEX)
• AVR-MT-128 buzzer demo code (C source and HEX)
• AVR-MT-128 relay demo code (C source and HEX)
• AVR-MT-128 misc demo code (C source and HEX)
• AVR-MT-128 UART demo code (C soruce and HEX)
• AVR-MT-128 test software CV
• AVR-MT-128 test software WINAVR+AVRSTUDIO
• AVR-MT-128 test software ICCAVR by Bob Gardner
• Weather station open source project by Landon Cox

AVR-H128CAN AT90CAN128 HEADER BOARD WITH ICSP AND JTAG CONNECTOR

INFO:

AVR-H128CAN is inexpensive way to develop and prototype circuits with AT90CAN128 without need to deal with SMD soldering. All microcontroller pins are available on extension header with 0.1" and power supply, oscillators, ICSP, JTAG are wired, so all you need to do is to connect your additional components to the AVR ports, as the step is 0.1" these headers perfectly fit the prototype sea of pad boards with 0.1" step.

FEATURES

• AT90CAN128-16AU microcontroller with 128KB Flash, 4KB RAM, 4KB EEPROM, CAN controller
• ICSP 5x2 pin connector for in-circuit programming with AVR-PG1 or AVR-PG2 or STK500 compatible programmer
• JTAG 5x2 pin connector for in-circuit debugging with AVR-JTAG-L or AVR-JTAG-USB
• 16MHz scillator circuit
• 32768 Hz oscillator circuit
• Reset IC ZM33064
• +5V voltage regulator LM78L05
• power supply filtering capacitors
• extension pin headers for each uC pin
• FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• dimensions 47x47 mm (1.85x1.85")

DOCUMENTS:

• AVR-H128CAN.pdf users manual

HARDWARE:

• AVR-128CAN schematic
• AVR ICSP connector (top view)

SOFTWARE:

• Blinking LED C source for WinAVR
• UART initialization C source for WinAVR

AVR-H128 ATMega128 HEADER BOARD WITH JTAG AND ICSP CONNECTOR

INFO:

AVR-H128 is inexpensive way to develop and prototype circuits with ATMEGA128 microcontroller without need to deal with SMD soldering. All microcontroller pins are available on extension header with 0.1" and power supply, oscillators, ICSP, JTAG are wired, so all you need to do is to connect your additional components to the AVR ports, as the step is 0.1" these headers perfectly fit the prototype sea of pad boards with 0.1" step.

FEATURES

• ATMega128-16AU microcontroller with 128 KB Flash, 4KB RAM, 4 KB EEPROM
• ICSP 5x2 pin connector for in-circuit programming with AVR-PG1 or AVR-PG2
• JTAG 5x2 pin connector for in-circuit debugging with AVR-JTAG or AVR-JTAG-USB
• 16MHz scillator circuit
• 32768 Hz oscillator circuit
• Reset IC ZM33064
• +5V voltage regulator LM78L05
• power supply filtering capacitors
• extension pin headers for each uC pin
• FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• dimensions 47x47 mm (1.85x1.85")

DOCUMENTS:

• AVR-H128.pdf users manual

HARDWARE:

• AVR-H128 schematic
• AVR ICSP connector (top view)

SOFTWARE:

• Blinking LED (C source and HEX)
• UART initialization (C source and HEX)

AVR-TLCD-128CAN - DEVELOPMENT BOARD WITH LCD DISPLAY WITH TOUCHSCREEN AND ATMEGA128

INFO:

AVR-TLCD-128CAN adds cool LCD and touchscreen interface to your next project. There is AT90CAN128 on board with all microcontroller pins available for plug-in additional boards

FEATURES:

• MCU: AT90CAN128 128KB Flash memory , 4096B RAM, 4096B EEPROM
• TOUCH SCREEN LCD 160x160 dots B/W 81x60 mm view area
• Stainless-steel front panel (102x85 mm 4x3.35") with easy to mount x4 3mm fixing screws
• JTAG connector for programming and debugging with AVR-JTAG-L or AVR-JTAG-USB
• ICSP connector for programming with AVR-PG1 or AVR-PG2
• SD-MMC card connector
• CAN driver and connector
• UEXT connector for connection to other Olimex modules like MOD-MP3, MOD-NRF24Lx, MOD-GPS and many others
• 16Mhz crystal
• Extension connectors for all AT90CAN128 ports
• PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print
• Dimensions: 102x85mm (4 x 3.35")

DOCUMENTS:

• AVR-TLCD-128CAN.pdf - Users Manual

HARDWARE:

• AVR-TLCD-128CAN schematic REV.A

SOFTWARE:

• AVR-TLCD-CAN test project for AVR Studio + GCC (WinAVR) C compiler

novice.pdf

0.15MB